sdkfz.10 final build…sort of

February 25, 2017

The last couple of days have not been idle.  I painted up a few figures and am currently working on the motorcycles by Zvezda.  Plastic Soldier company has a deal for 11 motorcycles for about $38.  It works out to $3.50 per machine.  Not bad.  They will be filling out the motorcycle units for the DAK forces.  Below are a couple of pics, not only of the first nearly completed cycle but also the detailed version of the sdkfz.10 card model I’ve been working on.

Front view.  Both need some paint touch up and perhaps a few more details on the motorcycles.

Front view. Both need some paint touch up and perhaps a few more details on the motorcycles.

The rear side view.  I think the half track came out pretty darned good!

The rear side view. I think the half track came out pretty darned good!

I am getting ready to design a CMP 15cwt truck.  There was a 1/87 scale version of the truck by Best Paper Models.  Their site was hacked a couple of years ago.  They’ve since entered an agreement with Betexa, another company who sells paper models.  Sadly, only 20 of their models have been uploaded so far and none of them are the CMP.  I’ve been waiting patiently for about 6 months.  The CMP does not look too difficult to design.  So…

This is about the cleanest blueprint I’ve seen to date.  I’m looking forward to this one.


Armored Car Company

February 19, 2017

These have been mostly finished and sitting on my paint table for a few weeks now.  I did not want to bring out the paints until my figures arrived from EWM.  Well, they did arrive yesterday and I spent some of the day today lining and touching up the models.  I think the results look pretty good!  All models by Paper Tiger Armaments.  Note that the sdkfz.222 also comes with a truck.  I have not built it…yet.

In search of the British army. sdkfz.231 in between two sdkfz.222.

In search of the British army. sdkfz.231 in between two sdkfz.222.

Upper front view.

Upper front view.

Rear view. Mission complete. Heading home!

Rear view. Mission complete. Heading home!

I suppose the extreme weathering with gray underneath is to show that they were hastily painted either before or after arriving in N. Africa.  Maybe they should have primed first?  😉


All (not so) Quiet

February 17, 2017

I have not been posting but have been a little busy over the past week.  The little General wanted me to build a Tiger Tank.  I rescaled Rawan’s Tiger I from 1:100 scale.  I think it came out well.  The other thing I’ve been doing is working on a sdkfz.10 artillery tractor.  Pictured on the right, it is the white template.  No tracks or wheels yet.  But those are pretty easy to do anyway.  I do need to adjust the front fenders, widening them and fixing the length.

img_4633

Side by side.  The half track is tiny!

Tiger Gun barrel is the length of a toothpick minus the tapered ends. 7/8″ of paper was wrapped twice followed by 7/16″ width of paper wrapped 3 times to get the tapered look of the gun. The muzzle break is 1/8″ of a medium kabob skewer.  The half track took me about 3 days to get to this point. I suspect I will have a detailed version this weekend.

The total build time of the Tiger was about 3 hours.  I think it took me about 1 hour to get the half track built to that point.  Maybe another half hour for tracks and wheels.

EDIT Here is the half track with wheels and tracks.  When I printed it out, I realized I forgot to duplicate the wheel.  Fortunately, there was a spare from my sdkfz.231 sitting on the table.

Wheels and tracks.

Wheels and tracks.


The Finished Product (mostly)

February 7, 2017

This is my final prototype.  I lowered the front edge of the front fenders a little.  I am unhappy with the window texture.  They are just to bright.  I am thinking a glass texture with a brown tint would be better.  Anyway, here are a few shots.  Included in one of the shots is a Kubelwagen by “Rawen” for size comparison.  It was a 1:100 scale model resized to 1:72 scale.  It comes with a Tiger I as well.  My son will be happy when I finally get that built.

Side/Rear shot to show off the rear "fenders". I simply added a circular strip of 67 lbs paper that was slightly larger than the wheel well. I've included 4 in the model just in case one gets messed up.

Side/Rear shot to show off the rear “fenders”. I simply added a circular strip of 67 lbs paper that was slightly larger than the wheel well. I’ve included 4 in the model just in case one gets messed up.

Front shot showing off the lowered front fender edges as well as the front bumper and windshield. I am not happy with the glass color.

Front shot showing off the lowered front fender edges as well as the front bumper and windshield. I am not happy with the glass color.

Overhead to show the basic interior print I added. Surprisingly effective with out much fuss. The roof will be permanently glues on.

Overhead to show the basic interior print I added. Surprisingly effective with out much fuss. The roof will be permanently glues on.

The axles are just 1" lengths of florist wire. Rough them up before gluing. I think the wire is about 20 gauge.

The axles are just 1″ lengths of florist wire. Rough them up before gluing. I think the wire is about 20 gauge.

Side by side with a quick build Kubelwagon by "Rawen."

Side by side with a quick build Kubelwagon by “Rawen.”

You can get the final model in jpg on the “Old School” page on this blog.

Quick notes: Cut out all of the black areas and discard.  The rear fenders make sure you do the black areas out first and then the outer edge.  I found it easier to cut the rear fenders with a knife being careful to leave enough paper to hold the piece in place.  Use 65-67 pound paper.  Some of the lines are not meant to be cut!  Print out at 85ppi for the correct scaling.

If you are new to card modeling, check out www.papermodelers.com.  Wonderful site full of very helpful folks!


Horch in color

February 7, 2017

I made some changes to the fender assembly and added a small bumper.  I eyeballed everything and luck was on my side.  The fenders and bumper were perfect lengths.

Front view with new fenders and bumper.  Not a great shot.  My

Front view with new fenders and bumper. Not a great shot. My “good” camera uses AA batteries and they went dead.

Rear view.  I used a straight edge when scoring most of the folds to get an ultra straight line.  The fold where the roof meets the body was not straight on my white prototype.  There was a small gap.  Perfect fit this time.

Rear view. I used a straight edge when scoring most of the folds to get an ultra straight line. The fold where the roof meets the body was not straight on my white prototype. There was a small gap. Perfect fit this time.

I still need to draw interiors.  I’ll also make a “roof down” option.  Finally, I forgot to draw in the rear fenders.  They don’t need to protrude as they are almost flush.  But they are supposed to be there and noticeable.


A Horch by Any Other Name…

February 6, 2017

One of those models that is most useful for any WW2 German Army is the Horch 108 as either the Type 1A or the Type 40.  The models used to be produced by Dragon and two in 1/72 scale could be had for about $20.  While not great, it was affordable.   Those, however, don’t seem to be in production anymore.  There is a MAC model (I think) but the price is at least $20 for just 1.  So, this weekend, I took it upon myself to make my own card model. Completely original work.  The following picks show only the template.  The details still need to be added to the model but the general shape is there.  The only thing missing really is the front bumper. I am thinking I need to widen the front fenders a little too.

 

An early prototype from Saturday. It was an exercise in understanding how the hood was supposed to angle and fold. Mostly pretty easy.

An early prototype from Saturday. It was an exercise in understanding how the hood was supposed to angle and fold. Mostly pretty easy.

A final build with all adjusted parts. The front fenders look a bit thin. I will either thin the wheels in the front or widen the fenders slightly. Front bumper still needs to be added.

A final build with all adjusted parts. The front fenders look a bit thin. I will either thin the wheels in the front or widen the fenders slightly. Front bumper still needs to be added.

My son said I needed to add the roof.  I was originally going to leave the roof off and add the folded ridge in the back.  He said he wanted it to look more like a truck.  Who is to argue with the little General, right?  Total build time of the final model was about 2 hours.  That could go more quickly with an assembly line.